Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
How do you really feel about How to Install a Bathtub Yourself?
Mounting a tub isn't precisely rocket science, but it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult project. If the old tub is readily available, the job can move immediately; if you need to open up a wall surface to remove the old tub and position the brand-new bathtub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also set in the new one. See to it you have actually certified yourself for the job and also fit attempting it. Rather than working with a service provider to take over a halfway-completed project, it is far better to take into consideration utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you mount a brand-new tub in your restroom if you have actually already purchased a new bathtub and also don't need to change the setup of your previous water system pipelines.
Your tools and product list need to consist of the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this process. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in place between the faucet and also the sink. Secure the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The previous type ought to be attached to the faucet ends first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Tub
Utilizing both wood boards under its feet, place the bathtub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest adaptable faucet adapter to the ideal supply pipe by making a compression join; after that do the exact same for the various other faucet.
Turn on the water system as well as inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and likewise inspect the overflow outlet and the normal outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bathtub needs to wait till the bath tub has actually been utilized a minimum of once as this will resolve it right into its last setting.
Preparing for the Installation
Firstly, the sustaining structure provided with the bath should be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, causing the water to permeate the wall in between the bathroom as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can split rather early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily offered on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy more info about A Step-by-Step Guide to Installing a Bathtub? Post a review below. We'd be pleased to see your thinking about this write up. We hope that you visit us again later on. Those who enjoyed our blog posting please remember to share it. Many thanks for your time. Don't hesitate to stop by our website back soon.
Further Details Report this page